How To Unclog a Bathtub Drain With Standing Water?

Knowing how to unclog a bathtub drain with standing water can save you money and time, not to mention the frustration of waiting for a plumber. Don’t worry, there are some easy steps you can take to fix the problem before you dial the number of your local plumbing company.

You’ll need a few things to unclog a bathtub drain with standing water: a pair of rubber gloves, rubber bands, a screwdriver, a snake, a plunge, and a bucket or bowl to scoop up excess water.

It’s important to get that water out as soon as possible. Why? Because when there’s standing water for too long, it becomes the perfect ground for bacteria and nobody wants that. It can also lead to mold and other problems.

How To Unclog a Bathtub Drain With Standing Water: Step By Step Guide

If your bathtub is draining slowly, or not at all, you may have a clogged drain. Everyone has to deal with this at some point, and it’s not as hard as it sounds.

In this section, we’ll show you how to unclog a bathtub drain with standing water step by step.

Before you start, gather the following tools:

– Some rubber gloves
– A bucket
– A plunger
– A snake or wire hanger
– Drain cleaner

How To Unclog a Bathtub Drain With Standing Water

First, find the drain. It’s probably somewhere on the bottom of the tub. It should look like a hole with a metal disc right above it. This is the drain cover.

Remove the drain cover from the bathtub with your hands or a screwdriver, if necessary.

If you need to use a screwdriver, be careful not to scratch the surface of the tub.

Now that your drain cover is out of the way, you need to find something that can reach pretty far down into your drain without falling apart too easily. Use a snake or wire hanger to hook out clogs in the drain pipe.

Put the plunger over the opening where you just removed hair and debris from inside the drain and work it vigorously up and down until you feel the pressure building up inside the drain.

You’ll hear some of the water rushing down into the pipes again. This is air pressure, so don’t worry.

Once you feel that pressure building, take off the plunger and run hot water down into your bathtub for about twenty seconds before putting in more drain cleaner.

Repeat this process twice more, then wait for fifteen minutes before turning on more hot water down the drain to finish clearing any debris caught in there.

How To Unclog a Bathtub Drain With Standing Water Naturally

The easiest and most budget-friendly way to unclog a drain with standing water naturally is to use solutions like vinegar, soda, and salt.

Here are some easy ways to use only natural ingredients.

Run hot water down your drain. The first step is to see if you can dislodge the clog with hot water alone.

It may be enough to break up the gunk that’s causing the clog. If hot water doesn’t clear the clog, try using boiling water and vinegar instead.

Pour 1 cup of baking soda down the drain, followed by 1 cup of vinegar. Just be sure you pour them in that order.

Wait 15-30 minutes before pouring boiling water down the drain again. The baking soda and vinegar should have created a chemical reaction that dislodges the gunk in your pipes.

How To Unclog a Bathtub With a Plunger

The water inside your bathtub and sink can drain slowly for a variety of reasons. It might be due to old pipes, a clogged drain, or a blockage deep in the plumbing.

If your bathtub is draining slowly, you may have to plunge the drain to remove the clog.

Plungers are inexpensive and easy to use. All you have to do is push and pull until the water starts to drain through the pipe again.

Here are the steps to unclog a bathtub with a plunger:

  1. Cover the overflow drain with a rag or wet washcloth. This prevents air from escaping through the overflow and gives you a better seal for working the plunger.
  2. Fill the tub about halfway with hot water to ensure that the bathtub is completely covered by the standing water. The more water there is, the easier it is to clear the drain.
  3. Place your plunger into your drain and pump it up and down several times to push air through the pipes and loosen any clogs in the pipes or trap.
  4. If this doesn’t work, try using a combination of baking soda and vinegar followed by hot water, or a chemical cleaner if necessary.
  5. This is the best way to unclog a bathtub drain with standing water with a plunger.

How To Unclog a Bathtub Full Of Water

The bathtub is one of the most used items in the bathroom, and it can easily become clogged.

I know that It can be frustrating if there is still water in the tub. You can’t simply plunge the drain or use a snake or auger to free up the blockage because of all the standing water.

But don’t worry, there are ways how to unclog a bathtub full of water and we’ll show you how.

  1. Pour 1 cup of baking soda into the drain. Fill it with hot water and wait for 20 minutes.
  2. Then, pour 1 cup of vinegar down the drain slowly. Wait for 10 to 15 minutes while the vinegar works its way through the clog
  3. Now, place your plunger in the drain area until it is completely covered with water.
  4. If you have an overflow drain in the tub, place a wet washcloth over it to prevent air from escaping.
  5. Using both hands, plunge up and down vigorously for about 20 seconds. If you feel resistance or hear gurgling, continue pushing and pulling until it stops.

That’s my favorite way to know how to fix this problem efficiently.

What To Do If Bathtub Won’t Drain Standing Water

If your bathtub won’t drain standing water, the first thing you should do is remove the strainer.

After removing the strainer, inspect the tub drain opening and use a flashlight to look down the drain pipe.

If you can see a clog, use a pair of needle-nose pliers to remove it. If removing it does not improve drainage, you may need to clean out the pipe using an auger.

This should loosen any built-up debris. If you’re unable to insert an auger into the pipe, you will need to remove the overflow plate to clean out both tub drains.

Now you know what to do if the bathtub won’t drain.

Home Remedy For Clogged Drain With Standing Water

A clogged drain is a common problem, especially in older homes. Most people will probably have to deal with this issue at some point.

This can happen anywhere in the plumbing system and is usually caused by the accumulation of grease, hair, soap, or food particles.

Chemical drain cleaners might seem like the quick fix for these problems, but they aren’t always effective and can be dangerous.

What is the best home remedy for clogged drains with standing water?

You can naturally clean drains with ingredients you probably already have in your kitchen.

  • First, pour boiling water down the drain. Use sodium bicarbonate and vinegar, a natural cleansing agent, to flush away debris.

Another way to clear a clogged drain with a natural solution is by using salt and baking soda together.

  • Once you’ve flushed out any standing water in the sink or tub, pour 1 cup of salt into the drain followed by 1 cup of baking soda.

How To Unclog a Tub Drain With Standing Water

To unclog a tub drain with standing water, start by using a plunger to try to clear the stoppage.

  1. Fill the tub with enough water so that the plunger is completely submerged in it, and then place the plunger over the drain so that it covers it completely.
  2. Use steady pressure to push and pull the plunger up and down several times before lifting it away from the drain.
  3. If that doesn’t work, you may need to try a plumber’s snake. Once you’ve cleared the blockage, try using a mixture of baking soda and vinegar.
  4. Mix 1/2 cup of baking soda with one cup of warm water and pour down the drain.
  5. Then, pour 1/2 cup of white vinegar down the drain and wait for 10 minutes. After 10 minutes, flush hot water down the drain for 5-10 seconds, then run cold water for 5-10 seconds.

Finally, if none of these things work, call your local plumber or call your landlord if you’re renting.

Standing Water In Tub After Drano

If you find that there is standing water in the tub after drano, then you will need to find the source of the problem.

If the drain is clogged and there is no air circulation, then the water will remain in there for an extended period of time before it evaporates.

In order to get rid of the standing water in the tub after drano, you will first need to determine where the clog is located. The easiest way to do this is by using a plunger.

A plunger works by pushing down on the clog to break it up so that air can circulate around it and dry out any excess moisture that may be trapped behind it.

Once you have found where the clog is located, place a bucket under the drain and cover it with a towel or cloth that has been soaked in warm water.

Let this stand overnight so that all of the remaining water will evaporate from the drain.

This will help to prevent any further problems from occurring.

How To Unclog Bathroom Sink With Standing Water

If your bathroom sink has standing water in it, you’re probably about to tear your hair out.

Unclog Bathroom Sink With Standing Water

You’ve got a clog, and you need to get rid of it fast. Here’s how to unclog the bathroom sink with standing water:

  1. Take off and remove the drain stopper from the bottom of the sink. It’ll be connected via a small metal rod that you may need to unscrew.
  2. If there’s hair that is stuck, you may be able to remove it using a zip tie or some other tool (a pair of needle-nose pliers might work).
  3. If that doesn’t work, you can use a plunger. Fill the sink up with water so that you can get a good suction going.

This should help dislodge whatever is stuck in there, but it may not work if it’s hair or something else that’s not easily dislodged from the pipes.

If your clog was caused by hair, then you may need to use drain cleaner at this point in order to dissolve the hair and allow it to be washed away with running water

How To Drain a Clogged Bathtub

If you’re wondering how to drain a clogged bathtub just follow these simple steps.

Step one: Get your supplies together. You’ll need a wire coat hanger, a bucket, and a plunger.

Step two: Take apart the wire coat hanger. Remove the hook end and straighten it out as much as possible, leaving a small bend at the end for maneuverability.

Step three: Put the bucket at the bottom of your tub to catch any excess water or clog that might pop out during the process.

Step four: Unscrew the drain cover from your tub and use it to fish out any visible hair and gunk that might be visible in the drain hole.

If you can’t get all of it with your fingers or a pair of tweezers, use the straightened wire coat hanger to grab more of it.

Step five: When all visible gunk has been cleared from your tub’s drain, run some hot water down to try to flush out anything that might still be stuck there.

That’s how to stop water from draining in a bathtub.

Questions and Answers

Will Drano Work in Standing Water?

The answer depends on the type of Drano being used. Some products are safe to use in standing water, while others are not.

Generally, if the product says that it can be used in standing water

How Do I Remove Standing Water From a Clogged Drain?

There are two ways to remove standing water from a clogged drain.

You can use a plunger that uses suction to dislodge the clog or use a drain snake, which is used to poke through the clog and break it up, so water can flow down the drain again.

Can You Pour Drain Cleaner in Standing Water?

Yes, you can pour drain cleaner in standing water, but you should not use chemical drain cleaners very often because they will damage your pipes over time.


If you are looking for a fast and efficient solution on how to unclog a bathtub drain with standing water, give it a try and if it worked for you, let us know!

Many people have had great success using our step-by-step guides to get rid of the blockage quickly. You may even be surprised at how easy it is!

Leave a Comment